SKR 1.4 unable to finish initial setup

[m4gn3to]

What happened

I have a Prusa Mk3s with a SKR 1.4 turbo.

I'm trying to complete the initial setup but always get the same error, when I reach the "T0 TOOLBOARD PREPARATION" step:

Error
Toolhead configuration cannot be deserialized, please check the configuration.
hotendFan: Required
partFan: Required

I've tried with another boards and the failure does not occur

What did you expect to happen

Continue the setup and generate config files.

How to reproduce

Get a SKR 1.4 turbo, flash it with Klipper and try to install Rat-Os 2.1.

Additional information

I'm using a Raspberry Pi 3b

[m4gn3to]

Hi.

I've downloaded latest version and now, the wizard ends fine.

But there is a little mess with the configuration.

The first error is that it includes a temperature_sensor for the LPC and it says it's unsupported.

Then, I've checked none input shaper but there is an error about probe points in resonance_tester.

Then, there is a mess with the pins aliases, there lack the exp ones and when I added them, there is an error with every pin alias declared as "null".

I have it running with this pin config:

[board_pins skr_14_turbo_tmc2209]
aliases:

steppers

x_step_pin=P2.2, x_dir_pin=P2.6, x_enable_pin=P2.1, x_uart_pin=P1.10, x_diag_pin=null, x_endstop_pin=P1.29,
y_step_pin=P0.19, y_dir_pin=P0.20, y_enable_pin=P2.8, y_uart_pin=P1.9, y_diag_pin=null, y_endstop_pin=P1.28,
z0_step_pin=P0.22, z0_dir_pin=P2.11, z0_enable_pin=P0.21, z0_uart_pin=P1.8, z0_diag_pin=null,
z1_step_pin=null, z1_dir_pin=null, z1_enable_pin=null, z1_uart_pin=null, z1_diag_pin=null,
z2_step_pin=null, z2_dir_pin=null, z2_enable_pin=null, z2_uart_pin=null, z2_diag_pin=null,
e_step_pin=P2.13, e_dir_pin=P0.11, e_enable_pin=P2.12, e_uart_pin=P1.4, e_diag_pin=null, e_heater_pin=P2.7, e_sensor_pin=P0.24,

accel

adxl345_cs_pin=null,

auto leveling

bltouch_sensor_pin=P0.10, bltouch_control_pin=P2.0,
probe_pin=P0.10,

fans

fan_part_cooling_pin=P2.3,
fan_toolhead_cooling_pin=P2.4,
fan_controller_board_pin=null,

Bed heater

heater_bed_heating_pin=P2.5,
heater_bed_sensor_pin=P0.25,

Expansion ports

EXP1 header

#################################################################
#EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
#EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=,
#############################------##############################

EXP2 header

#################################################################
#EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=, EXP2_10=,
#EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=,
#############################------##############################

Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2"

display_rs_pin=P1.19,
display_e_pin=P1.18,
display_d4_pin=P1.20,
display_d5_pin=P1.21,
display_d6_pin=P1.22,
display_d7_pin=P1.23,
display_encoder_pin1=P3.26,
display_encoder_pin2=P3.25,
display_click_pin=P0.28,
display_beeper_pin=P1.30,

#filament_sensor
filament_switch_sensor_pin=P1.26,

[mcu]
serial: /dev/btt-skr-14-turbo

[aljko223]

Have you been able to resolve the issue?

[m4gn3to]

No.

From time to time I try to finish the wizard, usually it does not finish...